Raspberry Pi Modell A+ (256MB SDRAM)

700MHz (ARM1176JZFS), 1080p, 3,5mm audio

Varenr: 132400
Alt. varenr: Raspberry Pi A+
275,-
-+
2 stk. på lager i butikk og på nett
BeskrivelseTilbehørAlternativer
Beskrivelse

The Model A+ is the low-cost variant of the Raspberry Pi. It replaced the originalModel A in November 2014. Compared to the Model A it has:

  • More GPIO. The GPIO header has grown to 40 pins, while retaining the same pinout for the first 26 pins as the Model A and B.
  • Micro SD. The old friction-fit SD card socket has been replaced with a much nicer push-push micro SD version.
  • Lower power consumption. By replacing linear regulators with switching ones we’ve reduced power consumption by between 0.5W and 1W.
  • Better audio. The audio circuit incorporates a dedicated low-noise power supply.
  • Smaller, neater form factor. We’ve aligned the USB connector with the board edge, moved composite video onto the 3.5mm jack, and added four squarely-placed mounting holes. Model A+ is approximately 2cm shorter than the Model A.

We recommend the Model A+ for for embedded projects and projects which require very low power, and which do not require Ethernet or multiple USB ports.


Raspberry Pi Model A+ Computer Board

The Raspberry Pi Model A+ is a tiny computer board that's up and running when a keyboard, mouse, display, PSU and MicroSD card with installed OS are added. It’s a miniature ARM-based PC which can run many of the applications that normally require a desktop PC, like spreadsheets, word-processing and games. It also plays High-Definition video. The model A+ features lower power consumption, better audio performance and a 40-pin GPIO connector amongst other improvements over the earlier model A. It is also even smaller! Raspberry Pi is an Open-Source product designed to be supported by Internet-based user forums. As a starting point refer to the Official website at: http://www.raspberrypi.org/.

Broadcom BCM2835 700MHz ARM1176JZFS processor with FPU and VideoCore IV dual-core GPU
GPU provides Open GL ES 2.0, hardware-accelerated OpenVG, and 1080p30 H.264 high-profile decode
GPU is capable of 1Gpixel/s, 1.5Gtexel/s or 24GFLOPs with texture filtering and DMA infrastructure
256MB SDRAM
HD 1080p video output
Composite video (PAL/NTSC) output
Stereo audio output
HDMI 1.3 & 1.4 video/audio socket
3.5mm 4-pole audio/composite video out jack socket
1 x USB 2.0 socket
15-way MPI CSI-2 connector for Raspberry Pi HD video camera (775-7731)
15-way Display Serial Interface connector
MicroSD card socket
Boots from MicroSD card, running a version of the Linux operating system (See Note below)
40-pin header for GPIO and serial buses (compatible with Raspberry Pi Model A 26-pin header)
Header footprint for JTAG connector
Power supply: +5V @ 2A via microUSB socket
Dimensions: 66 x 56 x 14mm
Firmware now looks for add-on boards that comply with the HAT (Hardware Attached on Top) design rules. This allows the Raspberry Pi A+ to set up the GPIO and load drivers to suit an expansion board automatically. For more information see: http://www.raspberrypi.org/introducing-raspberry-pi-hats/

Let op:

Accessories available separately: Power supply: 822-6373 , MicroSD memory card with NOOBS software: 820-9791

Supplied with

Getting Started guide

Tilbehør
Alternativer
Varen er på lager.
Varen er bestilt fra leverandør og leveringsdato er bekreftet.
Varen er bestilt fra leverandør, men leveringsdato er ikke bekreftet.
Varen må bestilles fra leverandør.
Varen befinner seg på fjernlager.
Varen er bestilt fra leverandør, men leveringsdato er ikke bekreftet.
Varene bestilles fra vår leverandørs lager.
Ubekreftet - Ta kontakt med kundesenter for nærmere informasjon.