140596
Varen er på lager.
Varen er bestilt fra leverandør og leveringsdato er bekreftet.
Varen er bestilt fra leverandør, men leveringsdato er ikke bekreftet.
Varen må bestilles fra leverandør.
Varen befinner seg på fjernlager.
Varen er bestilt fra leverandør, men leveringsdato er ikke bekreftet.
Varene bestilles fra vår leverandørs lager.
Ubekreftet - Ta kontakt med kundesenter for nærmere informasjon.

 Handlevogn

Handlevognen er tom.
 


Nyhetsmail

Motta nyheter per epost.

EK-FC1070 GTX - Acetal+Nickel

nVidia GTX 1070

Oslo
2
Trondheim
0
Varenr:
138525
Lev.Produktnr.:
3831109831489
Netto: 1 149,-
 ink. mva.

Netto: 919,-   eks. mva.

Kjøp

138525  3831109831489 EK-FC1070 GTX - Acetal+Nickel nVidia GTX 1070
138525  3831109831489 EK-FC1070 GTX - Acetal+Nickel nVidia GTX 1070
Lenker: Produkt | Produsent | Support

Details

EK-FC1070 GTX is a high-performance full-cover water block for NVIDIA® GeForce GTX 1070 Founders Edition graphics cards. Please check our Cooling Configurator online compatibility system for detailed compatibility list!

This water block directly cools the GPU, RAM as well as VRM (voltage regulation module) as water flows directly over these critical areas, thus allowing the graphics card and it's VRM to remain stable under high overclocks. EK-FC1070 GTX water block features a central inlet split-flow cooling engine design for best possible cooling performance, which also works flawlessly with reversed water flow without adversely affecting the cooling performance. Moreover, such design offers great hydraulic performance allowing this product to be used in liquid cooling systems using weaker water pumps.

PHOTO HERE

The base is made of nickel plated electrolytic copper while the top is made of quality POM Acetal material. The top also features two pre-drilled slots for 3mm LED diodes. The sealing is ensured by quality rubber washers. Screw-in brass standoffs are pre-installed and allow for a safe and painless installation procedure.

EK Water Blocks recommends the purchase of aesthetic retention backplate (EK-FC1070 GTX Backplate - Black or Nickel) which improves the looks of your graphics cards and also provide some passive cooling to the circuit board VRM section.

G1/4" threaded fittings can be used on both sides of the FC Terminal. Up to four EK-FC1070 GTX water blocks can be used on a single ATX form factor motherboard by using EK-FC Terminal (DUAL, TRIPLE or QUAD type) system or other means of interconnectivity. Please note that EK-FC Bridge & Link system is not compatible with this water block.

Enclosed:
- EK-FC1070 GTX series water block 
- Mounting mechanism with screw-in brass standoffs
- Thermal pads
- Thermal grease EK-TIM Ectotherm (1g)

Made in Slovenia - Europe!

 

PLEASE NOTE:

  • Due to an immense variety of fittings/barbs available on the market and no prescribed standards, we guarantee compatibility only for connectors bought from our web site.
  • NVIDIA® GeForce GTX 1070 factory backplate is not compatible with this water block!
  • New NVIDIA® SLI HB bridges are not compatible with this water block. You can still use regular SLI bridge that comes with every SLI supported motherboard.

Additional Info

Material / Design / Color optionNickel Acetal
ThreadsG1/4
Chip ManufacturerNvidia GeForce


Copyright © 2017 Digital Impuls AS - All rights reserved
Forretningssystem og netthandel er levert av MultiCase™ Norge AS

(3.16.10.19)